Looking for:
Singer tiny serger manual download. Singer Tiny Serger TS380 |
SINGER TINY TAYLOR TT INSTRUCTION MANUAL Pdf Download | ManualsLib.The Singer Tiny Serger: A Little Gem — The Mermaid's Den
Check that bobbin case is in proper posi- tion. Install spool cap on spool pin. Slide spool of thread onto spool pin. Pull thread from spool and, using two hands, pull it through diagonal slit in first thread guide. First thread guide should look like this when properly threaded. Feed end of thread through small hole in top of bobbin from the inside, leaving a 3" tail. Slide power switch into ON Position Hold end of thread the "tail" firmly and step on foot switch until a few coils are wound onto bobbin and stop.
Pull the thread toward you so that it hooks on notch A at 3 o'clock position and then 1. Insert wound bobbin into bobbin case with pull to the left so that it passes through thread spooling off to left side, as shown. The diagram at right shows an overview of the threading procedure; refer to the specific instructions below for important details.
Your spool of thread should be in the same position as it was for winding the bobbin, on the spool pin on the back of the machine. Turn handwheel toward you until take-up lever is in highest position. Pass thread through hole in take-up lever C from right to left. Turn handwheel toward you so that needle lowers and thread guide D is accessible. Place thread behind thread guide D to the right side, and pull forward. Hold top needle thread and turn hand- wheel toward you until needle goes to its lowest and then its highest point.
Raise the presser foot using the presser bar lifter. Gently pull top needle thread until lower bobbin thread comes up in form of a loop. Set stitch control knob to desired stitch length. For most mending, the "long stitch" setting is acceptable. Turn hand wheel toward you to raise nee- dle to highest position. Lift presser foot using presser bar lifter. Make sure that both needle top thread and bobbin lower thread are pulled straight back behind needle about 4".
The bobbin case tension is pre-set at the factory and cannot be adjusted. The tension level may be determined by using two different color threads for the nee- dle and bobbin threads, and then analyzing the resulting stitches.
Turn handwheel to raise needle to its high- est position. Loosen needle clamp screw just enough to remove needle. A small screwdriver may be helpful.
With flat side of needle to the right same side as needle clamp screw , insert new needle up into clamp as far as it will go. In the event that the bobbin case becomes displaced and does not move freely or pops out completely, follow the three easy steps below. When you plug in the foot pedal cord, the threading light goes out. There's no built-in light for sewing. The Tiny Serger has one needle and two loopers. You thread it in this order:.
At certain points during the threading process, you'll have to turn the handwheel to move the loopers around to get them out of your way for threading.
You'll definitely need tweezers to thread this serger. The accessories tray comes with some tweezers, but I ended up using the tweezers that came with my other serger, which were a little smaller and gave me a better grip on the thread. If you have trouble threading this machine with the tweezers it comes with, try using slightly smaller ones. Threading the machine from scratch is a little difficult, just because the space inside the machine is so cramped.
The thread paths themselves are easy to follow, but maneuvering the thread in the small space is a bit difficult. It is doable; it just takes a bit of time and finesse to get the machine threaded properly. The open space between the side of the machine and the needle plate is a little less than one inch.
For easier threading, the manual recommends tying on new threads and advancing the new thread through the thread paths by turning the handwheel see a tutorial here. Don't let your knot go through the needle, though, as it could break it. It takes a regular sewing machine needle style , size 14 , which is convenient. The flat side of the needle should face backward. I recommend getting Schmetz needles in bulk, as they're the most reliable and well made needles I've found.
The presser foot on this machine can't be removed, and you have to push the presser bar down to lift the foot, which takes a little getting used to, since you lift it up on most machines. There are no numbers on the tension dials--just an indicator for more or less tension. I have a lot of vintage sewing machines , so I'm used to numberless dials. I set my dials to the default, which matches up the dots on the machine and the dial, and this seemed to work well on medium-weight cotton.
The thread stand can expand to fit bigger spools. Serger cones will fit on the spool pins, but they're a bit wobbly. On my other serger, I have spool holders on each of the spool pins, which do a better job of holding the cones in place, but you might want to make or buy a thread stand to put behind the machine if you want to use serger cones regularly. There's no blade to cut the fabric as you serge, so you'll have to make sure your edges are nice and straight before you begin sewing.
There is a fabric guide that helps you line things up to make sure the stitches are right on the edge of your fabric. The Tiny Serger has two speed ranges, Lo and Hi, which is convenient. Here are the finished samples.
The Tiny Serger makes a nice three thread overlock stitch! It's a lot better than I was expecting from such a tiny machine. The stitch is certainly on par with my regular serger. The Tiny Serger should be oiled before or after each use. In reviews I've seen of this tiny serger, people seem to either love it or hate it, so it has a polarizing effect.
Personally, I love it, and I'm surprised that Singer stopped making them. I hesitated to get a serger because of the expense, but if I'd known about the Singer Tiny Serger, I'd have bought one right away.
It doesn't have all the bells and whistles of a bigger machine, but it does a great job of finishing raw edges, which is mostly what I use my regular serger for. Can use regular thread or serger thread. Thread stand expands to fit larger spools, and two different sizes of spool caps are included with the machine. Some people also add bigger thread stands behind the machine.
Fabric guide is helpful for keeping your stitching right on the edge of your fabric. Threading light helps you see what you're doing inside the machine. Great for small spaces, travel, or just having a backup serger.
Has two different speed ranges, which can both be used with the pedal i. There's an accessory compartment underneath the machine for handy storage. There's no knife, so there isn't a huge accumulation of fuzz and fluff every time you serge, and the machine doesn't require much cleaning.
You can only find them used, so condition may be an issue. I can't speak to the hardiness of this serger--mine works great, but I might have gotten lucky to find one in good working condition. On a similar note, due to size and the fact that it's not made anymore, it would be difficult to get this machine repaired or serviced. The presser foot can't be removed.
Comments
Post a Comment