Looking for:
SAFETY 1ST GROW AND GO INSTRUCTIONS MANUAL Pdf Download | ManualsLib |
Safety 1st grow and go manual
To make adjustments for smaller infants, see pages Fully Loosen Harness Cover Out of Shell and Straps Pad Push down on harness release lever under flap on front of seat pad while pulling out on harness straps as shown. Any slot can be used when adjustment levers inward. Move the headrest up or down to 7. Reach Under the Seat the proper height for your child. Between Base and Shell See page 5 for fit guidelines.
Make sure it is securely locked into Pull metal retainer completely place. Pull up on buckle to make sure it is secured. The buckle MUST not Do not use this child restraint rear facing unless the top of your childs head is at least 1 in. Slide end of tops of your childs ears are above the top of the buckle cover into buckle slot in child restraints headrest in its highest position.
WARNING: Failure to place buckles metal retainer Failure to follow these steps can result in serious injury completely through pad and shell can result in serious or death. The headrest MUST be in the lowest position. Fully Loosen Harness Straps Push down on harness release lever 2.
Lift Pad Off of Front of under flap on front of seat pad while Child Restraint pulling out on harness straps as shown. Pull Harness Straps Out of 4. Replace Pad and Check The buckle MUST not pull out. Place Child in Child Thread harness straps through slots in Restraint headrest pad.
The childs bottom and back should Thread harness straps through lower be flat against the child restraint. Position harness strap over childs shoulders and thighs. DO NOT twist harness straps. Pull up on harness strap to make Attach 2nd Harness Strap sure buckle is locked. Correct 4. Pull on harness adjustment strap The harness strap must be returned to the upper shoulder to tighten harness snugly.
Failure to follow these steps can result in serious injury or death. Position Chest Clip 1 This child restraint has 3 positions: The chest clip must be placed at 2 mid-chest even with armpits and 3 Rear Facing - 2 and 3 away from the childs neck.
For children who cannot sit up unassisted, the level line on shell MUST be parallel with the ground. For children who can sit up 6. Check Harness Tightness unassisted, you may rotate the Try to pinch the harness at the child restraint to be more upright in shoulders vertically between index position 2.
NOTE: When forward facing, the reclined positions are to be If you can pinch the harness strap, tighten more. The harness used only to install the child restraint and booster seat flush straps should be snug throughout their length.
Vehicle seat back must be upright. WARNINGS: Failure to fasten and tighten the harness system correctly may allow the child to be ejected from the child restraint in a crash or sudden stop causing serious injury or death.
To recline, pull out on recline handle and push top of child restraint back. Do not mistake comfort for safety. Harness system must be snugly adjusted. For upright, pull out on recline handle and pull top of child restraint Snug harness straps should not allow any slack. They lay in forward. They do not press on the childs flesh or push the childs body into an unnatural position.
Loosen Harness Strap 2. Unbuckle Harness 3. Release Chest Clip 4. Only store the harness system when converting child 5. Adjust the Headrest restraint into a booster seat. Fully Loosen Harness Straps Push down on harness release lever under flap on front of seat 6.
Locate Buckles Metal Retainer 7. Pull Headrest Pad Off Fully recline the child restraint and Bottom of Headrest reach under the seat between the As Shown base and shell and through the re- cline handle. Rotate metal retainer and push it up through shell and pad. From Top of Seat, 8. Headrest As Shown To remove accessories see page Adjust the Headrest to the Highest Position Undo Fasteners on the headrest.
Headrest Pad As Shown Tighten Harness Pull on harness adjustment strap to remove any slack from the harness system. Pull Headrest Pad Down 4. Pull Headrest Pad Off 9. Failure to do this can result in serious injury or death.
Make sure harness covers are closed so fastening strips are not exposed. Do not use bleach. Tumble dry separately for minutes on low heat. Remove immediately. Cleaning Harness Strap Spot clean using warm sudsy water and damp cloth. Replacing Pad Adjust the headrest to the highest position.
Starting from the bottom, gently pull headrest pad onto headrest. Pull Pad Down and levers. Slide harness straps into slots in pad. Attach fasteners. Off of Bottom of Starting from bottom of child restraint, slip pad on shell. Pull Harness Holders harness adjustment strap through pad. Wrap pad around bot- Pull up to remove completely. Push harness holders through slots in pad. Push pad behind headrest. Wrap around the top of shell. Adjust the Headrest 1. Fully Recline the Child to the Highest Position Restraint Pull out on recline handle and push top of child restraint back.
Undo Fasteners on Seat and Headrest Pad and 2. You MUST on side of headrest. Any slot can be used when Pull chest clip, harness straps, and forward facing.
Learn more. Safety First has developed a car seat that is versatile, safe and very easy to install. It can be installed in less than five minutes and is compatible with all car models. The Safety 1st Grow and Go 3-in-1 Car Seat has a lot of great features: it offers a luxurious, comfortable ride for children, has machine-washable covers and is one of the lightest seats in the marketplace.
It's a simple solution to the problem of installing car seats in vehicles. The straps of the Safety 1st Grow and Go can be washed. A rating of how compatible, easy and secure a child car seat can be correctly installed in certain test vehicles. This rating is based on a rear-facing installation using the vehicle belts Safety First has developed a car seat that is versatile, safe and very easy to install. It can be installed in less than five minutes and is compatible with all car models.
Safety 1st has a wide range of baby car safety products to keep your baby safe. The road ahead is comfortable and secure when your little one rides in a Safety 1st car seat. Feed the buckle's metal retainer through the slot on the seat pad. Five different ways to get bluetooth in your car. Leasing a car can be complicated, but if you know what you're doing, it can save money. Safety 1st ; Installation Type.
Latch ; Color. Carbon Ink ; Orientation. Adjustable Headrest C. Head Pillow see page 24 D. This allows the seat to be secured with seat belts. Read the manual of the car seat for details. There are Isofix car seats that can't be secured with seat belts. This was helpful share. What is the safest location to place a car seat?
Verified This partially depends on the car, but generally speaking the middle of the back seat is the safest place. Here the child is as far away as possible from the sides and thus best protected in case of an accident. However this only the case if there is a full 3-point seatbelt.
The DJG family is committed to creating car seats substituted. Prices are subject to change. Applicable with the most comfort and convenience available today. Print page 1 Print document 42 pages. Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account?
Comments
Post a Comment